Parr-instrument PDM User Manual

Browse online or download User Manual for Sensors Parr-instrument PDM. Parr Instrument PDM User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 12
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
Meter Installation in 4838 Reactor Controller
1. Unplug the power cord of the 4838 controller. Remove the (2) screws located on the top
corners of the rear panel on the controller. Gently lift the cover, which is hinged at the
bottom, forward taking care not to apply tension on any wiring internally.
2. If applicable, remove and discard the black
hole plug on the sloped front panel. This can
be done by pinching the clasps on the back of
the plug from the inside of the front plate.
3. Insert the controller through the panel cutout,
from outside in, making sure the rubber gasket
is on the outside of the controller front panel.
(If wires are preinstalled, remove the terminal connector by releasing the tabs on the sides of
the 2082E meter and gently pulling the terminal connector off. Reference photos below.)
Slide the white mounting bracket onto the 2082E with the mounting screws pointing towards
the front panel. Slide the mounting bracket forward until it touches the controller panel. The
clasps on the mounting bracket should align with the groves on the 2082E. Gently tighten
the screws until the 2082E is held into place. (If removed, reattach the terminal connector.)
Terminal Connector Removal
I
I
I
n
n
n
s
s
s
t
t
t
a
a
a
l
l
l
l
l
l
a
a
a
t
t
t
i
i
i
o
o
o
n
n
n
I
I
I
n
n
n
s
s
s
t
t
t
r
r
r
u
u
u
c
c
c
t
t
t
i
i
i
o
o
o
n
n
n
s
s
s
f
f
f
o
o
o
r
r
r
P
P
P
r
r
r
e
e
e
s
s
s
s
s
s
u
u
u
r
r
r
e
e
e
D
D
D
i
i
i
s
s
s
p
p
p
l
l
l
a
a
a
y
y
y
M
M
M
o
o
o
d
d
d
u
u
u
l
l
l
e
e
e
(
(
(
P
P
P
D
D
D
M
M
M
)
)
)
i
i
i
n
n
n
4
4
4
8
8
8
3
3
3
8
8
8
R
R
R
e
e
e
a
a
a
c
c
c
t
t
t
o
o
o
r
r
r
C
C
C
o
o
o
n
n
n
t
t
t
r
r
r
o
o
o
l
l
l
l
l
l
e
e
e
r
r
r
No. 562M
Page view 0
1 2 3 4 5 6 ... 11 12

Summary of Contents

Page 1

Meter Installation in 4838 Reactor Controller 1. Unplug the power cord of the 4838 controller. Remove the (2) screws located on the top corners

Page 2

- 10 - PDM Installation This page left blank intentionally.

Page 3

- 11 - PDM Installation This page left blank intentionally.

Page 4

Revision 05/15/09 Parr Instrument Company 211 53rd Street • Moline, Illinois 61265 USA 1-309-762-7716 • 1-800-872-7720 • Fax: 1-309-762-9453 E-mai

Page 5

- 2 - PDM Installation Meter installation in 4838 Reactor Controller (continued) Meter Installation Diagram 4. Mount the 2068E power supply, o

Page 6

- 3 - PDM Installation Wiring installation in the 4838 Reactor Controller 1. If applicable, remove the black hole plug on the back of the contro

Page 7

- 4 - PDM Installation Wiring installation in the 4838 Reactor Controller (continued) 5. Find the loose 3-pin edge connector, with yellow and w

Page 8

- 5 - PDM Installation Wiring installation in 4838 Reactor Controller (continued) 8. Find the orange wire #8, with both ends stripped, and attac

Page 9

- 6 - PDM Installation Final Steps Close the controller and replace the two screws on the back panel. Plug the 4838 controller back in, and turn

Page 10 - PDM Installation

- 7 - PDM Installation Wiring Schematic

Page 11

- 8 - PDM Installation Pressure Module Defaults Keys command: 1. Press “SET” to select 2. Press return key move to next operation mode 3. Up/

Page 12 - Parr Instrument Company

- 9 - PDM Installation Pressure Module Defaults (continued) Press and hold down “SET” for 5-sec Operation Mode Select type/value Comment InPt

Comments to this Manuals

No comments